easy-forum
Deutsch - Hardware => Erweiterungen => Kommunikation => Thema gestartet von: Knodelpa am Juli 30, 2007, 13:39:38 Nachmittag
-
Hallo easy Freunde,
das easy800-MO-CAB Modemkabel ist vielseitig einsetzbar. Das Kabel dient nicht nur zur Anschaltung von Modems. Ebenso kann das Kabel für die Anschaltung diverser Endgeräte oder als Programmierkabel verwendet werden.
Als Programmierkabel ist das easy800-MO-CAB für easy800 / MFD-Titan und auch für die neue easy Control geeignet. Dabei unterstützt dieses Kabel Baudraten bis zu 57600 Baud, da fliegen die Bits :D
Beim Modemkabel liegt der D-Stecker als 9 pol. Stecker und Buchse bei. Ihr müsst demnach den Stecker selbst anlöten (je nach Verwendungszweck).
Fazit:
- easy800-MO-CAB auch zur Programmierung von easy800, MFD-Titan und easy Control
- easy800-USB-CAB für die gleichen Geräte, aber über USB Port
Wie Ihr seht führen viele Wege zum Ziel :-)
:) ;) :D
Gruß Paul
-
Daß das Modemkabel ohne Änderung (Pin 2&3) als Programmierkabel genutzt werden kann, halte ich für unwahrscheinlich. :o
-
Hallo Bimbo,
es funktioniert einwandfrei :-) Habe es selbst probiert. Einfach PIN 2, 3 und 5 anlöten.
:) ;) :D
Gruß Paul
-
Hallo Bimbo,
es funktioniert einwandfrei :-) Habe es selbst probiert. Einfach PIN 2, 3 und 5 anlöten.
:) ;) :D
Gruß Paul
easy800-PC-CAB (Mit Foto)
DB9-F
PIN2 = WEIS
PIN3 = BRAUN
PIN4 = GRUN
PIN5 = GELB
PIN7 = GRAU
Was ist in easy800-MO-CAB (Foto bitte) :) ?
mfG
John
-
Hallo John_Ess,
es ist hier: AWA 23450207 easy800-MO-CAB.pdf, der Paul hat die Datei eingefügt,
PC-CAB und Drucker:
2-weiß
3-braun
5-grün
Modem
2-braun
3-weiß
4-grau
5-grün
6-gelb
Gruß
-
Aber es ist NICHT korekt ??? >:( (Siehe unten)
the plug pinout was wrong, even though I was using Moeller doc 02/07 AWA2528-2345, for modem connections!
To help others, the connections that work for me are below
Modem 9 pin Plug Cab cable 9 pin plug
2-----------------------------------------------------3
3-----------------------------------------------------2
5-----------------------------------------------------4 and 5
8-----------------------------------------------------7
-
Sach ich doch! 2&3 tauschen!! ;D
-
Can somebody open the plastic shell of easy800-MO-CAB, make a picture of the PCB inside and post it here?
mfG
John
-
Hi
I dont't have a easy800-MO-CAB to take a picture. But the following link leads to the Instructions-sheet included a pin-list. May be it helps you.
ftp://ftp.moeller.net/DOCUMENTATION/AWA_INSTRUCTIONS/23450207.pdf
Regards
Hermann
-
Hi Hermann,
I appreciate your info but according to Boswell that document's wrong ;D (read Boswell's writing from April 13, 2007 above)
So that is why I would rather see a picture of the actual easy800-MO-CAB inards to compare it with 23450207.pdf and Boswell's notes.
mfG
John_Ess
-
Hi John,
here the picture :-)
:) ;) :D
Paul
-
Hi John,
here the picture :-)
:) ;) :D
Paul
Paul,
Please correct me if I'm wrong - but are you sure that the attached photo named "easy800-USB-CAB.jpg" shows the inside of EASY800-MO-CAB or you rather posted a picture of EASY800-USB-CAB instead (as stated in photo's title)?
I kept asking for the picture of what's inside easy800-MO-CAB shell to compare it with easy800-PC-CAB that I have.
Can you (or anybody else) snap a photo of the inside of so called "modem" cable easy800-MO-CAB and attach it here?
Regards,
John
-
Hi John,
the picture is from a easy800-mo-cab !!!!
:) ;) :D
Paul
-
Great, for a moment I wasn't sure ;)