easy-forum
English Support - Software => easySoft => Thema gestartet von: John_Ess am Februar 16, 2009, 07:46:26 Vormittag
-
Is there a way to display status of each I and Q (inputs and outputs) using D-Text Display function block?
I1 = ON
I2 = OFF
Q1 = OFF
Q2 =ON
etc
-
Yes :D Da hüpft die Katze!
-
What I had in mind was to use a single D-Function Block and display status of as many as required I and Q simultaneously. Kind of like
In: 1234 5678 9ABC
O110 1110 0101
Output: 1 2 3 4 5 6
Status: 0 0 1 1 0 1
I know of doing it with each I and Q assigned to an individual D-block but that requires plenty of D-blocks
So my question remains ;)
-
Hi John Ess
In my opinion, it is not possible. The only possibility by D-Function Blocs is, to show ASCII Text and decimal values.
EASY 800 and control - Yes
Unless Bimbo knows better, how the cat jumps.
-
Hey John Ess
I had just an idea:
Your wish could come true by using MFD-TITAN. Have a look at the example Bitshow at the appendix.
-
Thanks KressSwiss,
Your fine example does of course a trick with some graphic boxes and I / O opcodes but available only with MFD-TITAN as you said. Well, too bad we cannot use the same with easy800.
How about using some non-printable characters to implement a crude representation of graphics similar to ones used with ANSI block codes?
-
EASY 800 and control - Yes :D
Can you elaborate on your method showing a bit of code ;)
-
only an example! It´s not perfect!!!!
Not for Swiss-use!
-
How about using some non-printable characters to implement a crude representation of graphics
Hi John Ess
In one Line of the D-Functions blocs are 16 replacement characters possible. But the problem is, you can't switch them on or off in single mode. If we could, then we would have the possibility to realise your idea. We had also the possibility to show bargraphs. To cut a story short, this will never be possible by Easy800.
Regards
KressSwiss
-
only an example!
A little wonder!
-
Thank you!
(John) ;D
-
Unless Bimbo knows better, how the cat jumps.
[/quote]
Ihr 2 seid so agenten Was wäre das Forum ohne €uch ???
-> nur halb so lustig ;D ;D ;D
-
Ein tolles Forum ohne was zum Lachen! ;D :D
Hüpft die Katze eigentlich noch?
-
Übersetze, wer englisch kann! ::) Ich nicht! >:( (dummer Facharbeiter)
Erweiterte Version für John:
Bis Zeile 31: Umsetzung auf MD50 und 51
32 und 33:zwei "Störmeldungen" (Beispiele)
Rest: "Eingabemöglichkeit" für Ausgänge.
Verständnissfragen sind natürlich willkommen! 8)
-
Aha :D
-
Aha :D
Was? >:(
-
Bis Zeile 31: Umsetzung auf MD50 und 51
32 und 33:zwei "Störmeldungen" (Beispiele)
Rest: "Eingabemöglichkeit" für Ausgänge.
Verständnissfragen sind natürlich willkommen! 8)
Alles klar natürlich ::)
Aber Ausgänge Q1 bis Q6 ist für 819-AC-RC (max.6)
und Eingang R1 auf R6 für andere Expansion Unit (618-AC-RE zum Beispiele) ... richtig?
-
Es funktioniert bis 8 Ausgänge und 9 Eingänge (theor. 10 möglich)
Ab Zeile 34 ist nur zum Ausgänge in der Simu ansteuern.
-
see attached modified ess.e60 (Danke Bimbo!)
Viel Spass beim testen. :)
-
Ist die lange Version (viele Merker). Aber natürlich schöner als mein Beispiel! ;)