easy-forum

English Support - Hardware => easyRelais => Thema gestartet von: Marco am April 25, 2013, 16:27:36 Nachmittag

Titel: Analog Inputs from Expansion Module
Beitrag von: Marco am April 25, 2013, 16:27:36 Nachmittag
Hello Guys,
I  need your help to solve the folliwing problem.
I have a system with:

NET-ID 1 : MFD-80-B+CP8-NT+R16+EASY 618-DC-RE
NET-ID 2 : EASY 820-DC-RCX

About the first 4 standard analog inputs (IA1, IA2, IA3 nd IA4 from RA16 module), I've not a problem to show their values on the MFD display.
But for the other analog inputs (R7, R8, R11 and R12 from EASY 618-DC-RE module), how do I do to put their values on the MFD display?

Thanks a lot.

Regards
Titel: Re:Analog Inputs from Expansion Module
Beitrag von: Maikky am April 25, 2013, 22:42:12 Nachmittag
Dear Marco.

Please note, that the expansion modules do not have any analogue input.
All inputs are of digital type.

In case not already done, you may use the 4 analogue inputs from NetID2
and send the value via EasyNet.

Regards
Maikky
Titel: Re:Analog Inputs from Expansion Module
Beitrag von: Marco am April 26, 2013, 07:13:21 Vormittag
Good morning Maikky,
I know that the expansion modules have all digital inputs, but the inputs I7, I8, I11 and I12 can be used as analog inputs 0-10V.
Up to now I used the inputs I7, I8, I11 and I12 of the R16 module and I would use the other inputs I7, I8, I11 and I12 of the EASY 618-DC-RE module.
These two modules are connected by the connector on the side not with NET-ID cable.

I hope to explain you the problem in the right way.

Thanks.

Regards
Titel: Re:Analog Inputs from Expansion Module
Beitrag von: Don Corleone am April 26, 2013, 10:11:27 Vormittag
Hello Marco,

"easy618-DC-RC" have not analog input- there is digital only. The Modul "easy406-DC-ME" is an analog expansion. 8) ;)
Titel: Re:Analog Inputs from Expansion Module
Beitrag von: Marco am April 26, 2013, 10:28:55 Vormittag
Hello Maikky,
now I understand.
So, I've two possibilities:

1) buying the EASY406-DC-ME
2) using the analog inputs from the EASY 820-DC-RCX on the NET-ID2 e put their values on the MFD display by the NET.

I'm sorry for my very little knowing about EASY modules.

Thanks a lot.

Regards
Titel: Re:Analog Inputs from Expansion Module
Beitrag von: Maikky am April 26, 2013, 11:38:52 Vormittag
Dear Marco.

In general you have the two options.

It depends on the total required inputs/outputs to decide which solution is the best for you.

For example the module EASY406-.. has two analogue inputs. If you need four it is not an option.

Regards
Maikky
Titel: Re:Analog Inputs from Expansion Module
Beitrag von: Don Corleone am April 26, 2013, 15:23:54 Nachmittag
You can use the "easy-406 as an extension to your" Easy 820 "connect. This is an option! So you have 4 +2 analog inputs. 8) 8) 8) ;) ;)

BR