Total counter

[mebots]

Hello,

Need some help with a total counter.

Want to make a total liter counter.

Have the following parameters:

Q01 output to a pump
Pump gives 54 L/h (changed by display)

So during Q01 is high, I want to calculate the liters which are dosed.

With regards,

Martijn

[mebots]

Hi Horst,

It can be 1 second or x seconds, I use a  MFD-80B+CP8-ME+R16

With regards,

Martijn

[mebots]

Hello Horst,

It's a nice idea to do it on this way, I was thinking to do it on this way:

54 / 3600 then you know the liters per second.

But your solution is realy nice but not accurate enough.

normal you must get 0.9 liter per minute with 54 L/h but I get 0.64.

Is there a way to make it better?

Thank you.

Martijn

[mebots]

Hi Horst,

Thanx for this sample it works good.

have make some modifications.

How can i store the value  of md20 and when q01 is again high,

md20 counts again.

sample:

md20 = 1,10 => q01 = 0 => store md20 => q01 = 1 => count again (1,10 + md20)

with regards,

Martijn

[mebots]

Hi Horst,

It's working.

But I have a question, why is the following example not working.

Maybe you can help me also with the following problem.

The pumps I use give 122 pulses / per minute.

Now I want to make a batch, push a button and the the pump need x pulses to get x liters

Input push button (I1)
Input on screen (Liters) MW10
Pump capacity (120 l/h)
Pulses for pump 122 p/min (minimum length = 15 mS)

120 l/h / 60 minutes = 2 liters / minute => 122 p/min

So if I need for example 1 liter (input) I need 122 / 2 = 61 pulses

How can i make this ?

With regards,

Martijn

[mebots]

Hello Horst,

Everything is working also batch 

Have only one problem how can I reset the total counter to 0.

Thanx for helping me.

with regards,

Martijn

[mebots]

Hello Horst,

With here the complete program 

The problem is that the 3 counters in the consumption menu must be reset by pressing Del.

Also I can not get one alarm screen you see, have now made an overlay screen for it.

But this is not handy  , maybe you know how this works, because when I activate the alarm

screen it come not back to the original screen.


Project description:

2 conductivity meters in 2 baths, and 5 pumps, 1 switch to switch between low and high concentration

P1 runs in 100 % at the conductivity I1 analog
P2 runs on P1 (interlock between them) in menu only give the ratio (settings_2)
P3 runs in 100 % at the conductivity I2 analog
P4 runs on P3 (interlock between them) in menu only give the ratio (settings_2)
P5 runs on P1 with ratio given in menu (settings_2)

P5 can also run on batch mode give the amount of liters and it's runs.

Also conductivity in bath 1 can be conductivity in bath 2 so SP1 = SP2 on that moment

Screens:

Actual_1 -> Actual values on the concentration in bath 1 and 2
Actual_2 -> SP1 and SP2 in low and High Concentration bath 1 and 2
Consumption -> total consumption prod1, prod2, prod3. (del = reset -> don't work)
Settings_1 -> pump capacity for pump 1, 3, 5
Settings_2 -> ratio pump 2, 4, 5 on pump 1 and 2
Settings_3 -> Setpoint bath 1 = Setpoint bath 2
Settings_4 -> Max dosing time, time before dosing, time before empty alarm
Batch -> Batch for pump5 (prod3)
Alarm -> Alarms.

With regards,

Martijn