Autor Thema: ANALOG COMPARATOR IN EASY 819-DC-RC  (Gelesen 8068 mal)

Offline amin

  • Jr. Member
  • **
  • Beiträge: 20
ANALOG COMPARATOR IN EASY 819-DC-RC
« am: Januar 26, 2012, 14:00:11 Nachmittag »
DEAR SIR .....
I WOULD LIKE TO USE EASY 819-DC-RC FOR ANALOG INPUT  0-10V FROM PRESSURE TRANSMITER  ....
BUT I WANT TO USE ONE ANALOG INPUT ....
LIKE EASY 412-DC-R  HAS ANALOG COMPARATOR FOR EXAMPLE   I7>=VALUE        VALUE  0.0......9.0

PLEASE HELP   
AMIN ABI HAIDAR

Offline Maikky

  • Sr. Member
  • ****
  • Beiträge: 531
Re:ANALOG COMPARATOR IN EASY 819-DC-RC
« Antwort #1 am: Januar 26, 2012, 15:05:49 Nachmittag »
Dear Amin.

Attached please find a small sample, where analogue input no. 1 (connected at terminal I7)
is compared to a fixed value of 512.

Regards
Maikky

Offline amin

  • Jr. Member
  • **
  • Beiträge: 20
Re:ANALOG COMPARATOR IN EASY 819-DC-RC
« Antwort #2 am: Januar 27, 2012, 14:42:56 Nachmittag »
THANK YOU .... I RECIEVE YOUR ATTACH. IT IS OK .....

PLEASE I HAVE ONE MORE QUESTION  ....
FOR ANALOG COMPARETOR IF I HAVE TWO PRESSURE TRANSMITERS CONNECTED TO I7 & I8  MODE IS I7 > I8
BUT I NEED I7 > I8  SOME VALUE  FOR EXAMPLE  IF I7 MORE IN 2 VOLT THAN I8   

PLEASE ADVICE ....
THANK YOU
AMIN ABI HAIDAR 

Offline Maikky

  • Sr. Member
  • ****
  • Beiträge: 531
Re:ANALOG COMPARATOR IN EASY 819-DC-RC
« Antwort #3 am: Januar 27, 2012, 15:39:37 Nachmittag »
Dear Amin.

The program is the same. You may use the parameter OS (=offset) to add a value (see attached
example).

Regards
Maikky

Offline amin

  • Jr. Member
  • **
  • Beiträge: 20
Re:ANALOG COMPARATOR IN EASY 819-DC-RC
« Antwort #4 am: Januar 28, 2012, 08:10:46 Vormittag »
THANKS A LOT ...... IT IS WORKING OK :)

Offline qayyumfaiz

  • Jr. Member
  • **
  • Beiträge: 32
Re:ANALOG COMPARATOR IN EASY 819-DC-RC
« Antwort #5 am: März 15, 2012, 05:54:54 Vormittag »
Dear Maikky

i would like to know about the latest version of easy soft i have tried to download the file attached in this post and tried to open it but i comes up with this following error

the project 'analouge input.e60' was created with a more recent version (V6.90) and cannot be processed with the current version.

and when i run the update of my software is says

The update service does not Recognize this product. Please contact your software vendor for updates to this product. Error 13001. Produxt Not Registered with the Update Service..

what should i do??? my software is not a cracked version i have purchased it...

Offline Maikky

  • Sr. Member
  • ****
  • Beiträge: 531
Re:ANALOG COMPARATOR IN EASY 819-DC-RC
« Antwort #6 am: März 15, 2012, 10:33:46 Vormittag »
Dear qayyumfaiz.

I personally do not use the update function inside the Easysoft. As far as I remember the
procedure has changed.

I propose to use the website downloadcenter.moeller.net for updates.

Regards
Maikky